I have a 2010 Roadglide custom which has ran great for the last 22,000 miles. While cruising in the 2200 to 2800 rpm range the bike has a momentary hesitation (hiccup) without a lost in rpms, any thoughts? The bike doesn't have any problems starting. The following modifications had been done after the first 1000 miles. Screaming eagle air kit, 2009 stock HD head pipe with the O2 sensors eliminated, V&H mufflers, Dobeck Performance EJK Gen 3.0 tuner.
I retrieved the codes below from speedometer:
The P0031, P0134, P0154 codes all make sense since the O2 sensors have been removed.
I have checked the battery voltage with the ignition off 13.08 volts, with ignition on 12.36 volts, at idle 14.16 volts, at 3000 rpms 14.28 volts.
I have done a resistance test of the CKP Sensor and it read 971 - 1025 ohms.
I have cleaned the pintle port in the throttle body.
I have also run a 1/3 of a bottle of fuel injector on the last tank of gas.
Any other suggestions?
Thank you.
DTC: P0031
FAULT CONDITION: O2 heater low/open
PRIORITY ORDER: 82
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0134
FAULT CONDITION: Front O2 sensor open/not responding
PRIORITY ORDER: 88
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0154
FAULT CONDITION: Rear O2 sensor open/not responding
PRIORITY ORDER: 89
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0505
FAULT CONDITION: Loss of Idle Sped Control
PRIORITY ORDER: 76
SOLUTION: 6.12 DTC P0505
DTC: P0113
FAULT CONDITION: IAT Sensor Voltage Open/High
PRIORITY ORDER: 59
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0374
FAULT CONDITION: CKP Sensor Synch Error
PRIORITY ORDER: 21
SOLUTION: 6.9 DTC P0373,P0374
I retrieved the codes below from speedometer:
The P0031, P0134, P0154 codes all make sense since the O2 sensors have been removed.
I have checked the battery voltage with the ignition off 13.08 volts, with ignition on 12.36 volts, at idle 14.16 volts, at 3000 rpms 14.28 volts.
I have done a resistance test of the CKP Sensor and it read 971 - 1025 ohms.
I have cleaned the pintle port in the throttle body.
I have also run a 1/3 of a bottle of fuel injector on the last tank of gas.
Any other suggestions?
Thank you.
DTC: P0031
FAULT CONDITION: O2 heater low/open
PRIORITY ORDER: 82
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0134
FAULT CONDITION: Front O2 sensor open/not responding
PRIORITY ORDER: 88
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0154
FAULT CONDITION: Rear O2 sensor open/not responding
PRIORITY ORDER: 89
SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154
DTC: P0505
FAULT CONDITION: Loss of Idle Sped Control
PRIORITY ORDER: 76
SOLUTION: 6.12 DTC P0505
DTC: P0113
FAULT CONDITION: IAT Sensor Voltage Open/High
PRIORITY ORDER: 59
SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113
DTC: P0374
FAULT CONDITION: CKP Sensor Synch Error
PRIORITY ORDER: 21
SOLUTION: 6.9 DTC P0373,P0374